How To Drain Sprinkler System Backflow

When this happens it can be fixed just like fixing a normal valve! This backflow pressure preventer is meant to work on portable water lines, and its assembly should help in giving protection when any potential hazards come up due to water contamination.

How To Winterize Your Sprinkler System Sprinkler

Find the main water valve to the irrigation system and turn it off.

How to drain sprinkler system backflow. Usually in your basement or crawl space. Make sure to have a bucket available for. Open the 2 petcocks (f) with a flat head screwdriver so that the screw head runs a 45 degree angle.

(usually located in the basement or crawl space) step 2: The diy lawn sprinkler installer, the landscaper or a handyman is not properly trained or licensed to test the proper backflow preventer that will protect your home and family. Most of the time its something very simple like the irrigation controller is turned off or has lost its programming due to a power loss or surge.

Once it has been attached test the sprinkler system for at least 10 minutes to make sure it is no longer leaking. If your irrigation system is attached to domestic water, it is required to have a backflow prevention device. Turn on one of your irrigation system zones (and leave it on).

Turn off the water supply by closing the main valve to the sprinkler system. This will ensure you turned the water off correctly and drain the pressure from the system. Open all the manual drain valves for each zone in the system, and leave them open so that all the water drains from the pipes and sprinkler heads.

Shut off valve in the normal operating position (on). Turn both test ports (5) to 45 degrees. Go outside and locate your backflow preventer.

Turn this off and open up the inlet drain valve, which will be located between the. Shut off sprinkler water supply valve (1) by turning to the right. Manual drain valve locate the manual drain valves situated downstream of each zone valve.

When the water draining from the device subsides, give the device a few light shakes to get a little more water out of the device. To blow out the system: Open all the manual drain valves for each zone in the system, and leave them open so that all the water drains from the pipes and sprinkler heads.

Using a small screwdriver, pull up the backflow preventer's stopper so it's touching the top of the casing (open). Allow all of the water to drain from the sprinkler heads. Backflow creates the potential for fertilizers, herbicides and other unwanted harmful substances to move from an irrigation system and into the public or potable water supply.

Adjust all ball valves and backflow test cocks to a 45 degree angle. Make sure you do this to all 4 ball valves. Referencing the diagram below, follow these instruction to perform a quick drain of your system:

Not only must they be licensed and file the proper permits and provide the mandatory backflow preventer performance test forms but they may unintentionally create a cross connection that could be potentially dangerous or even lethal. Go to the controller and turn on an irrigation or sprinkler zone. Go outside and turn all of the ball valves on your backflow to a 45 degree angle as pictured below.

This allows the water inside the backflow to drain from the unit. Thanks to its drainage hole, you can drain any remaining water in the pipe after you are done, and this will help to prevent further contamination. Turn the water off to your sprinkler system.

We offer dallas sprinkler system and irrigation system installations that use only high quality lawn sprinkler, drip irrigation, drainage, french drain and landscape. The basics of draining a sprinkler system for the winter. It is tagged as drain valve.

If you find that the irrigation controller isnt the culprit, check the city water meter to make sure you have a water supply to the backflow. This leaves water remaining from the inside of the backflow preventer all the way to the main valve underground. Shut off valve in the off position.

Open each of the valves in the pipes to release the water pressure. All you have to do is turn off the water at the water main, clean the valve and reattach it to the lines. The drain for your system may be located outside near the backflow or may be in your basement.

A sprinkler system can stop working for many reasons. Power up your sprinkler system, and then shut it offyou should see the auto valve drain once the pressure is off. Open the inside drain (b) to drain your system.

If the system has a pump, it should be drained, removed from the system and stored inside. Install the 1/4 quick disconnect fitting into one of the test cocks on the backflow preventer. Over 25 years of professional, licensed installation experience.

When you blow out your sprinkler system, you typically blow air from the front side of your backflow preventer into the network of sprinkler pipe. Before burying the sprinkler line again, take some measurements and draw a map or add it into your sprinkler planogram, as a reminder of where all of. Steps how to drain your sprinkler / irrigation system:

Related posts about backflow preventers. Leave them open for a few days, if possible. Turn off your water at the dedicated sprinkler line shutoff (a) in your basement / crawlspace.

If this is not possible, drain the pump and wrap it to insulate it from the weather.

Sprinkler Fitter Job Description eHow Sprinkler, Fire